1. Adjust the position of compressed air cylinder

将型材放到该机工作台面上，两锯片的夹压紧气缸调整至对工件压紧合适的位置，然后固定压紧气缸。

Put the profiles on the working table of the machine, adjust the clamping cylinder of the two saw blades to the most suitable position for pressing the workpiece, and then fix and press the cylinder tightly.

1、锯片进给速度的调节

1. Adjustment of saw blade feed speed

在试机过程中，如果觉得锯片的进给速度不合适时，可以调节工进缸调速接头，使进给速度增大或减小，就可得到所需要的进给速度。

During the testing process, if the feeding speed of the saw blade is not suitable, the speed regulating joint of the work intake cylinder can be adjusted, and the feed speed is increased or decreased, so the required feed rate can be obtained.

2、锯削角度调整

2, sawing angle adjustment

机床按上述各项调整完毕，并检查符合规定后试运转30分钟，如果没有发生异常现象，就可进行以下调试。

The machine tool has been adjusted according to the above, and checked after the test run 30 minutes, if there is no abnormal phenomenon, you can carry out the following debugging.

2.1、 90°角的调整(锯片伸出与工作台面垂直)

2.1, 90 degree angle adjustment (saw blade extends to the working surface vertical)

机床出公司前均调试并经检验合格,在此可直接锯切一型材检验90°角的锯切面是否符合要求,机床锯切初始角度设为90°,误差为±10ˊ。如若不符合要求，可调整摆角板下面的螺栓的高低，重复锯切测量，使之满足要求。然后锁紧其上的螺母。

A machine before the company are debugging and passed the test, this can be directly cutting a test section 90 angle cutting surface meets the requirements, the sawing machine initial angle is set to 90 degrees. The error is about 10'. If not meet the requirements, you can adjust the height of the bolt below the swing plate, repeat sawing measurement, so that it meets the requirements. Then lock the nut on it.

2.2、 45°角度的调整(锯片伸出与工作台面夹角成45°时设定为45°，下同)

Adjust the angle of 2.2 and 45 degrees (when the angle between the protrusion of the saw blade and the working table is 45 degrees, set to 45 degrees, the same below)

松开工作台上的锁紧手柄，转动手柄，抽出支撑杆再转动手柄，使之摆至45°角锯切型材，检验其45°是否符合要求，误差为±10。如果不符合要求，可调整拖板上的限位螺栓的高低，再重复锯切、测量，使之满足要求，然后再锁紧螺栓上的螺母，拧紧锁紧手柄。

The locking handle on the worktable is loosened, the handle is rotated, the supporting rod is drawn out, and the handle is turned, so that the saw bar is cut to the angle of 45 degrees, and whether the 45 degree meets the requirement is checked, and the error is 10. If not meet the requirements, you can adjust the height of the limit bolt on the carriage, and then repeat sawing, measuring, so as to meet the requirements, and then lock the nut on the bolt, tighten the handle tightly.

2.3、-45°角度调整

2.3, -45 degree angle adjustment

松开锁紧手柄，转动手柄，把摆角板转至大于-45°时插入定位杆，然后手柄回转摆角板压在定位杆上，锯切一型材，检验其45°是否符合要求，误差10°，如果不符合要求，可调整扇形块上的限位螺钉的高低，重复锯切、测量、使之满足要求，然后再锁紧螺钉上的螺母，拧紧锁紧手柄。

Loosen the locking handle, the handle is rotated to swing angle plates to more than -45 degrees are inserted into the positioning rod, and the handle rotary swing angle of pressure plate on the positioning rod, sawing a profile, test whether the 45 degrees to meet the requirements, the error of 10 degrees, if you do not meet the requirements, can adjust the level of fan-shaped block limit screw, sawing, repeated measurement, so as to meet the requirements, then the lock nut on the screw and tighten the locking handle.

3、切削型材长度调整

3, cutting profile length adjustment

角度调整完毕后，应调整工件的切割长度。拨动“拖板选择”开关至“左”或“右”位置。按下“拖板启动”按钮，使锯头运动至所需要加工长度的近似位置，松手，在把“拖板选择”开关拨至“停”位置。转动手轮，同时看着游标尺，使右机头定位至准确位置，刻度尺指示长度就是工件长边的长度。

After adjusting the angle, the cutting length of the workpiece should be adjusted. Toggle the carriage selection switch to the left or right position. Press the start button of the carriage, move the saw head to the approximate position of the required length, and let go of the switch to the stop position. Turn the handwheel, and watch the ruler at the same time, so that the right head is positioned to the correct position, and the scale indicates that the length is the length of the long side of the workpiece.

4、操作

4, operation

开总电源机关→调整二机头角度→调整副标尺箭头→机头选择置“双”位置→选择拖板电机方向→启动拖板电机→拖板位置手动微调→右机头刹紧→启动锯切电机→放料→旋转旋钮夹紧→按动工进按钮→松开工进按钮→松开夹紧→取料

The total power to adjust the open angle, two organs, adjust the vice ruler arrow head selection set "double" position, choose to start the carriage motor direction, the carriage motor, carriage position, manual adjustment right head locking to start cutting motor, feeding, clamping, rotating the knob to start button according to feeding button to loosen loosen the clamping and Reclaimer

5、停机

5, stop

停机前，机器应空载运行2分钟，观察机器运行状况，确定无异常后，关闭电源，切断气源停机。

Before shutdown, the machine should run no-load for 2 minutes, observe the operation of the machine, determine the no exception, turn off the power supply, cut off the gas supply stop.

更多的关于济南vi设计的问题或者详细的内容，请进入我们公司的网站：http://www.facons.cn网站中会有很多的内容仅供参考。

More questions about Ji'nan VI design or detailed content, please go to our company's website: http://www.facons.cn site will have a lot of content for reference only.